Evaluation of 3D Printed Modified Twin Block for Correction of Skeletal Class II Malocclusion in Growing Females

NCT ID: NCT04028661

Last Updated: 2019-07-23

Basic Information

• Recruitment Status: UNKNOWN
• Clinical Phase: NA
• Total Enrollment: 20 participants
• Study Classification: INTERVENTIONAL
• Study Start Date: 2019-08-01
• Study Completion Date: 2020-07-01

Brief Summary

The study is to evaluate the effect of 3D printed modified Twin Block Appliance on skeletal Class II profile correction.

The null hypothesis of this research is that use of 3D Printed Twin Block is not able to induce skeletal rather than dental effects for correction of the skeletal Class II malocclusion in comparison with untreated growing Class II control subjects.

Detailed Description

I- For the treatment group:

A- Medical History Questionnaire will be filled by the patient to exclude the presence of any systemic condition.

B- Clinical Examination:

Proper examination of the oral structures including;

• Teeth will be examined for caries, fracture or missing teeth
• Gingival tissues will be examined for gingivitis, periodontitis, attachment loss, gingival recession, oral lesions and the nature of the gingival biotype.
• Thorough intraoral examination is needed to evaluate the need for referral for consultation or intervention before the initiation of treatment.

C- Diagnosis:

• The patient is checked to fulfil the inclusion criteria.
• A clinical visualized treatment outcome (VTO) will be done by asking the patient to bite in an advanced position and check the outcome of this advancement on the patient"s profile. Patients with positive results (better profiles were achieved upon advancement) are included in the study.
• Full set of records (including standardized Lateral Cephalograms) will be taken for every 8 patient as part of the routine procedure for treatment of patients in the outpatient clinic of the Orthodontic Department, Cairo University.

D- Clinical Procedures:

After taking upper and lower impressions, the impressions are then poured into hard stone that are then digitally scanned using 3D laboratory scanner (3Shape R500 Lab Scanner).

Designing the appliance is done on upper and lower virtual models (using 3Shape Appliance Designer). The appliance covers the upper and lower dental arches with lingual horizontal rectangular attachments to increase the retention.

Buccal triangular ramps for mandibular advancement are designed. They are positioned buccal to the upper and lower posterior segments with a lock to ensure the desired mandibular advancement.

3D printing of the appliance is then done using 3D printer (Dent2-Mogassam) with biocompatible resin material (NextDent Resin OrthoRigid).

Post curing using ultraviolet light for 30min using postcuring unit (Postcuring- Mogassam).

The appliance is then delivered to the patient and instructions are given. Follow up every 4 weeks for 8 months or edge to edge occlusion (the sooner) and then full records taken including Lateral Cephalogram.

II- For the Control group

• The subjects should be fulfilling the previously mentioned inclusion criteria and should sign the informed consent of agreement to be recruited in the study.
• According to the randomization sheet, the patients allocated to the control group will be immediately referred for the uptake of a Lateral Cephalogram which will be considered (T1) without any treatment procedures.
• A "no treatment" phase of 8 months will be carried out through which the patients will be followed up to monitor any factor that might have occurred to exclude the patient from the study.
• Another Lateral Cephalogram will be taken after 8 months (T2).
• T2 images are to be considered the initial diagnostic images for the patient. The patients will be then assessed and treatment will be provided for each patient as required.

Conditions

Class II Malocclusion, Division 1

Study Design

• Allocation Method: RANDOMIZED
• Intervention Model: PARALLEL
• Primary Study Purpose: TREATMENT
• Blinding Strategy: SINGLE

Study Groups

Intervention group

use of 3D printed Modified Twin Block Appliance.

Group Type: EXPERIMENTAL

3D printed Modified Twin Block Appliance

Intervention Type: DEVICE

It is a functional appliance for mandibular advancement designed digitally on virtual models.

Untreated control group

No treatment phase of 8 months.

Group Type: NO_INTERVENTION

No interventions assigned to this group

Interventions

3D printed Modified Twin Block Appliance

It is a functional appliance for mandibular advancement designed digitally on virtual models.

Intervention Type: DEVICE

Eligibility Criteria

Inclusion Criteria

• Females 10-13 years of age.
• Skeletal Angle Class II division 1 malocclusion with a deficient mandible. (SNB ≤ 76°)
• Horizontal or neutral growth pattern. (MMP ≤ 30°)
• Increased overjet (min 5 mm) with Class II canine relationship. (minimum of half unit)
• Cervical Vertebral Maturation (CVM) stage 3.

Exclusion Criteria

• Systemic Disease.
• Any signs or symptoms or previous history of temporomandibular disorders (TMD) as clicking, crepitus, pain, limitation or deviation.
• Extracted or missing upper permanent tooth/teeth (except for third molars).
• Facial Asymmetry.
• Para-functional habits.
• Severe proclination or crowding that requires extractions in the lower arch.

• Minimum Eligible Age: 10 Years
• Maximum Eligible Age: 13 Years
• Eligible Sex: FEMALE
• Accepts Healthy Volunteers: Yes

Sponsors

Cairo University

OTHER

Sponsor Role: lead

Responsible Party

: Donia Ayman Ahmed Ezzeldin ElSayed

Master degree student

Responsibility Role: PRINCIPAL_INVESTIGATOR

Principal Investigators

Donia Ezzeldin, Master

Role: PRINCIPAL_INVESTIGATOR

Cairo University

Central Contacts

Donia Ezzeldin, Master

Role: CONTACT

donia.ayman@dentistry.cu.edu.eg

01001200089

Other Identifiers

1993

Identifier Type: -

Identifier Source: org_study_id